Insulating Your Floors

Do the floors in your home feel cold? This may mean there is no insulation between you and your unheated basement or crawlspace. Fortunately, Owens Corning® insulation products and our floor insulation guide make it easy to insulate your floors.

What’s your R-value?

Below are the U.S. Department of Energy recommended minimum R-values for your climate zone.

Your Climate Zone: 4

    Attics 2x4 Walls 2x6 Walls Floors Crawlspaces
Zone 4 R38 to R60 R13 to R15 R19 to R21 R25 to R30 R25 to R30

Choosing the Right Insulation

Fiberglass insulation is sold in roll and batt form; both are available with or without kraft paper facing. Use the guide below to select the best insulation for your project.

  • Rolls

    • Easy to transport
    • Must be cut to length
  • Batts

    • Pre-cut for fast installation
    • Preferred for new installation
  • Faced

    • Kraft paper vapor retarder attached
    • Use as first layer/new construction
  • Unfaced

    • No vapor retarder
    • Use when adding to existing insulation


To calculate how much you need:

To determine the size of the area you are insulating, follow these steps:

  1. Measure the length of the floor joists you want to insulate. Remember to measure the width between the floor joists so you select the correct insulation width.
  2. Use the Square Footage Calculator below and let us help you calculate the quantity of packages you will need for your project. (Square Footage of floor area divided by square foot coverage area on the product package).

Calculate Your Square Footage



Your Square Footage: Sq Ft.

Recommended Products

The following products are recommended for use in floors. Add items to your list, and you’ll be able to view, print or email your checklist when you’re done.

Loading Products…

Installation Tips

Installation Instructions

  1. Install the insulation so that it maintains continuous contact with the subfloor above. Any gaps between the floor and the insulation can allow air movement that reduces the insulation R-value. Make sure the insulation expands to its full label thickness (any areas of compression will also cause a reduction of R-value).
  2. The insulation should be installed all the way back at the end of each joist run so that it touches the band joist. You want complete coverage under the house. There will usually be a narrow joist space on the walls that run parallel to the joist. The insulation should be cut to fit this space.
  3. There are often both pipes and wires in crawl spaces under floors, and occasionally there will be a junction box. You may need to cut or split the insulation to fit it around electrical wiring, boxes and drain pipes.
  4. Likewise, the insulation will have to be cut or split so that it fits around cross braces. Do not leave voids (uninsulated areas) or overly compress the insulation.
  5. To support the insulation, use nylon banding or metal insulation supports. Wood furring strips can also be used.
  6. Install a 4- to 6-mil polyethylene ground cover to keep ground moisture from rising up into the space. All joints / seams in the poly should be overlapped a minimum of 6" and sealed. The ground cover should run up the crawl space wall, on all sides, a minimum of 6" and be sealed to the wall.

NOTE: Do not leave faced insulation exposed. The facings on kraft-faced insulation will burn and must be installed in substantial contact with an approved interior finish as soon as the insulation has been installed. Facing must be installed in substantial contact with an approved ceiling, floor or wall material. Keep open flame and other heat sources away from facing. See package for warnings, fire hazard and instructions, or call 1-800-GET-PINK®. Check your local building codes for requirements in your area.

Basic Tools

  • Tape measure
  • Utility knife
  • Straightedge or 2 x 4 (for cutting insulation)
  • Lightweight, squeeze-type stapler

Protective Gear

  • Work gloves
  • Loose-fitting, long-sleeved shirt
  • OSHA-approved safety glasses
  • Disposable dust mask

Special Equipment

  • Portable work light


Before you begin any insulation project make sure you:

  • Seal any open penetrations
  • Gather the necessary tools and wear protective gear listed above
  • Always use a portable work light to ensure you have enough light in your work environment
  • Leave EcoTouch® PINK® insulation in its wrapper until you are ready to use it
  • Packaged insulation is highly compressed and expands greatly when the wrapper is opened

Owens Corning is fully committed to safety and believes accidents are preventable. Please join us by promoting safety where you live and work.