Insulating Your Basement Walls

Insulating basement walls can potentially decrease your home heating and cooling costs, and you can complete the project in a weekend.* If your basement is “conditioned” (heated or cooled by a furnace or air conditioning unit), only the walls need to be insulated.

What’s your R-value?

Below are the U.S. Department of Energy recommended minimum R-values for your climate zone.

Your Climate Zone: 2

    Attics 2x4 Walls 2x6 Walls Floors Crawlspaces
Zone 2 R30 to R60 R13 to R15 R19 to R21 R13 R13 to R19

Choosing the Right Insulation

Fiberglass insulation is sold in roll and batt form; both are available with or without kraft paper facing. Use the guide below to select the best insulation for your project.

  • Rolls

    • Easy to transport
    • Must be cut to length
  • Batts

    • Pre-cut for fast installation
    • Preferred for new installation
  • Faced

    • Kraft paper vapor retarder attached
    • Use as first layer/new construction
  • Unfaced

    • No vapor retarder
    • Use when adding to existing insulation


To calculate how much you need:

Before EcoTouch® insulation can be installed, a 2" x 4" stud wall, usually 16" on-center*, must be built.

  1. Measure the height and the length of each of your basement walls. Don’t forget to measure the width of the space between the wall studs, so you’re sure which products to choose.
  2. Multiply the wall’s height by the wall’s length.

Calculate Your Square Footage



Your Square Footage: Sq Ft.

Recommended Products

The following products are recommended for use in basements. Add items to your list, and you’ll be able to view, print or email your checklist when you’re done.

Loading Products…

Installation Tips

Installation Instructions

  1. Either faced or unfaced insulation can be used in basement walls. Faced insulation should be placed between the studs with the vapor retarder facing the interior of the room in heating climates. In this example, we’re using R-13 insulation, which has a kraft-facing vapor retarder. The insulation batt can be friction fit or the flange on the facing can be stapled to the inside or face of the stud. For an alternative product option and ease of installation, select Owens Corning PROPINK FastBatt® for your interior basement wall project. PROPINK FastBatt® is a fiberglass insulation batt with a flangeless kraft facing. This product is designed for a friction fit application, requiring no stapling to hold the batt in the cavity. It should be installed so that the cavity is completely filled, fitting snugly at the sides and ends. In addition, the kraft facing provides a vapor retarder membrane required by most building codes.
  2. For the band joist, use unfaced cut-to-fit pieces of EcoTouch™ PINK® insulation and place them snugly into the space.
  3. With either faced or unfaced insulation, an interior finish material such as drywall should be installed as soon as the insulation is in place.

NOTE: Do not leave faced insulation exposed. The facings on kraft-faced insulation will burn and must be installed in substantial contact with an approved interior finish as soon as the insulation has been installed. Facing must be installed in substantial contact with an approved ceiling, floor or wall material. Keep open flame and other heat sources away from facing. See package for warnings, fire hazard and instructions, or call 1-800-GET-PINK®.

Check your local building codes for requirements in your area.

Basic Tools

  • Tape measure
  • Utility knife
  • Straightedge or 2 x 4 (for cutting insulation)
  • Lightweight, squeeze-type stapler

Protective Gear

  • Work gloves
  • Loose-fitting, long-sleeved shirt
  • OSHA-approved safety glasses
  • Disposable dust mask

Special Equipment

  • Portable work light


Before you begin any insulation project make sure you:

  • Seal any open penetrations
  • Gather the necessary tools and wear protective gear listed above
  • Always use a portable work light to ensure you have enough light in your work environment
  • Leave EcoTouch™ PINK® insulation in its wrapper until you are ready to use it
  • Packaged insulation is highly compressed and expands greatly when the wrapper is opened

Owens Corning is fully committed to safety and believes accidents are preventable. Please join us by promoting safety where you live and work.

* Savings vary. Find out why in the seller’s fact sheet on R-values. Higher R-values mean greater insulating power.